Aimpoint Acro P2 Dedicated Optic Cut (Irons in Rear) for Glock

This is a service to cut your factory Glock slide for the Aimpoint Acro P2 optic. This is an Acro P2 specific cut, we do not guarantee fitment with other optics that use a similar footprint. This cut allows you to keep your irons to the rear of the optic. To accomplish this, we will cut away your factory iron dovetail and cut a new one further back on the slide. By doing this, it allows us to get a deep Acro P2 cut and not break into the safety plunger or any other internal components while still maintaining the irons behind the optic. The rear portion of the slide where the new dovetail is located will be .080" lower than the rest of the top of the slide due to cutting away the factory dovetail. We recut the radii on the corners so that the back portion blends in to the rest of the slide. The lowest point of the optic will sit at about .180" below the top surface of the slide.

Note: This is only offer on standard 1" width slides at this time, we are not offering the larger G20/21/29/30 or Gen 5 G22/23 slides at this time.

**Please note: This is a dedicated cut for the P2 that we designed in order to have your iron sights to the rear of the slide. If you are looking for the standard Acro footprint we offer, you can find that here: https://wagermachineworks.com/product/glock-aimpoint-acro-p1-p2-footprint-optic-cut-also-fits-steiner-mps/

Recommended Sights for Lower 1/3 Co-witness:  Due to the rear dovetail being moved, your rear sight will need to be .080" taller than it normally would be to be a match for the front sight. We recommend a .255" tall front sight and a .335" tall rear sight. We do offer sights that can be purchased with this cut here: https://wagermachineworks.com/product/dawson-precision-iron-sights-for-glock-dedicated-acro-p2-cut/

IRON LOCATION: This cut has been designed to allow the rear irons to remain behind the optic. In order to do this, we have to cut away the factory dovetail in order to move it back far enough to fit the Acro P2 cut. We do not offer an "Irons Forward" Setup with this cut. If you are looking for that, please look at our Standard Acro Footprint Cut.

COATINGS: There is also an option to add Cerakote or Black Nitride to the slide. We offer the Cerakote in Graphite Black, FDE, ODG, Tungsten and Burnt Bronze and it will be applied to the entire slide.  If the Cerakote option is chosen, we will remove your channel liner and install a new one after coating. We also now offer a black nitride coating. The nitride is a much harder finish than the Cerakote and will not wear as quickly. It is similar to many factory coatings and offers a clean uniform black look. We work with a local company to offer the nitride, so lead times are not guaranteed. Estimated 3-4 weeks total turnaround. Due to the amount of bare metal that will be visible with this cut, we do not offer the cold blue finish.

For detailed coating descriptions, please see our Coatings Explained Page: https://wagermachineworks.com/coating-options-explained/

THE PROCESS: Once you checkout with your chosen optic cut you will receive an email with instructions on how to ship the slide to us. Please ship us your stripped slide only (barrel and recoil spring removed), we are not an FFL and cannot handle frames! We will complete the cut and/or Cerakote and then ship the slide back to you quickly! You will receive an email once the slide has been shipped back to you.

TIMELINE: Once we receive your slide, we will complete the work in the stated turnaround time (Mon-Fri) or less and get it shipped back to you. This includes coating.

PLEASE NOTE: Your order will be returned to the address that you provide at checkout. Please follow instructions and include a copy of your confirmation email when you ship your slide to us, failure to follow this will result in increased turnaround time.

DISCLAIMER: This product is not manufactured, authorized, endorsed,
or warranted by GLOCK. GLOCK does not warrant or represent that
this product is compatible with GLOCK pistols.