Holosun 509 ACSS (NOT 509T) Footprint Optic Cut for Glock
$85.00 – $170.00
This is a service to cut your factory Glock slide for a Holosun 509 ACSS optic (aftermarket slides cut with prior approval). This will not fit the standard Holosun 509T, that cut is available separately as it is different. The cut will be .165" deep at its lowest point if it is cut in front of the factory irons or it will be .250" deep at its lowest point if the irons are moved in front of the optic.
Recommended Sights for Lower 1/3 Co-witness: Angry Bear Arms Suppressor Height Sights (slightly taller than 1/3)
IRON LOCATION: You may choose to keep your irons in the factory location, which will mean the optic sits in front of the rear iron sight. We also offer an iron sight relocation service where the optic will be cut to the rear of the slide and the iron sight dovetail will be recut in front of the optic.
COATINGS: There is also an option to add Cerakote or bluing to the slide. We offer the Cerakote in Graphite Black, FDE, ODG, Tungsten and Burnt Bronze and it will be applied to the entire slide. The cold bluing will be applied to just the area we cut and your factory finish will remain everywhere else. This type of finish is not as consistent and visually appealing as the Cerakote, but offers some protection for the bare metal. If the Cerakote option is chosen, we will remove your channel liner and install a new one after coating. We also now offer a black nitride coating. The nitride is a much harder finish than the Cerakote and will not wear as quickly. It is similar to many factory coatings and offers a clean uniform black look. We work with a local company to offer the nitride, so lead times are not guaranteed. Estimated 3-4 weeks total turnaround.
For detailed coating descriptions, please see our Coatings Explained Page: https://wagermachineworks.com/coating-options-explained/
THE PROCESS: Once you checkout with your chosen optic cut you will receive an email with instructions on how to ship the slide to us. Please ship us your stripped slide only, we are not an FFL and cannot handle frames! We will complete the cut and/or Cerakote and then ship the slide back to you quickly! You will receive an email once the slide has been shipped back to you.
TIMELINE: Once we receive your slide, we will complete the work in the stated turnaround (Mon-Fri) or less and get it shipped back to you. This includes coating.
PLEASE NOTE: Your order will be returned to the address that you provide at checkout. Please follow instructions and include a copy of your confirmation email when you ship your slide to us, failure to follow this will result in increased turnaround time.
DISCLAIMER: This product is not manufactured, authorized, endorsed,
or warranted by GLOCK. GLOCK does not warrant or represent that
this product is compatible with GLOCK pistols.
Additional information
| Weight | 1 lbs |
|---|---|
| Dimensions | 11 × 4 × 3 in |
| Model | Glock 17, Glock 19, Glock 19x, Glock 20, Glock 21, Glock 22, Glock 23, Glock 26, Glock 27, Glock 29, Glock 30, Glock 31, Glock 32, Glock 33, Glock 34, Glock 35, Glock 36, Glock 37, Glock 38, Glock 39, Glock 45 |
| Iron Sight Location | Keep Factory Location, Move In Front of Optic |
| Coating | None, Black Nitride (Increased Lead Time), Blue the Cut Area, Graphite Black Cerakote, FDE Cerakote, OD Green Cerakote, Tungsten Cerakote, Burnt Bronze Cerakote |
1 review for Holosun 509 ACSS (NOT 509T) Footprint Optic Cut for Glock
You must be logged in to post a review.
Wes M –
Optic cut and nitrate coat took 2 weeks from order to in hand. Thats unheard of! I was plesantly suprised at the accuracy of this optic cut. Upon placing my optic, I precieved it as not being able to fit. However, realizing my error it sat right into place with ZERO wiggle or movement. Thank you so much for your work! Will recommend.